- Captured using Sony a9 w/ Voigtlander 15mm lens. 
- Reconstructed with RealityCapture
- Cleaned up w/ MeshMixer

Elevator in Berlin - Realities.io

*MP5* **K** (**K**urz - *Short*) - shortenned version of MP5 submachine gun. *Barrel lenght = 115mm. 9x19mm Parabellum, Roller-delayed blowback.*

low-poly HK MP5K

## Scanning
Scanning was done in sPC connected mode (WiFi, with latest update 120FPS speed) at a moderate high point distance of 0.15mm (can go up/down to 0.05mm but at 0.15mm it already resulted in a 20M triangle file...) until target quality was reached. Keep an eye on ideal scan distance since it reduces with increasing point distance. When you are too far away scanning will be drastically slower compared to when you're in the ideal distance. 

## Post-Processing
When finishing the single scans it already creates a point cloud so I only had to align using automatic feature alignment (after deleting all unnecessary data from around the object). Afterwards I used Quicksurface to align the scan to the coordinate system and reduce the triangle count to a manageable 4M triangles.

Wax Statue Virgin Mary - Einscan Rigil

## Scanning
Scanning was done in PC connected mode (WiFi, with latest update 120FPS speed) at a moderate high point distance of 0.15mm (can go up/down to 0.05mm but at 0.15mm it already resulted in a 20M triangle file...) until target quality was reached.
I placed the casting on bed of marker cards and geometries so I can also capture the sides of the casting which I also use for aligning the two scans I created (top and bottom). The scan itself was performed with both cross and parallel line mode taking roughly 5min for scanning. No scan spray was used for scanning.

## Post-Processing
When finishing the single scans it already creates a point cloud so I only had to align using automatic feature alignment (after deleting all unnecessary data from around the object). Afterwards I used Quicksurface to align the scan to the coordinate system and reduce the triangle count to a manageable 4M triangles.

Wax Casting Traditional Scene - Einscan Rigil

## Scanning
Scanning was done in PC connected mode (WiFi, with latest update 120FPS speed) at a moderate high point distance of 0.15mm (can go up/down to 0.05mm but at 0.15mm it already resulted in a 15M triangle file...) until target quality was reached. Keep an eye on ideal scan distance since it reduces with increasing point distance.
I placed the statue on bed of marker cards and geometries so I can also capture the sides of the statue which I also use for aligning the two scans I created (top and bottom). The scan itself was performed with both cross and parallel line mode taking roughly 5min for scanning. No scan spray was used for scanning.

## Post-Processing
When finishing the single scans it already creates a point cloud so I only had to align using automatic feature alignment (after deleting all unnecessary data from around the object). Afterwards I used Quicksurface to align the scan to the coordinate system and reduce the triangle count to a manageable 4M triangles.

Wood Statue Boy with Dog - Einscan Rigil

## Scanning
Scanning was done in PC connected mode (WiFi, with latest update 120FPS speed) at a moderate high point distance of 0.15mm (can go up/down to 0.05mm but at 0.15mm it already resulted in a 15M triangle file...) until target quality was reache
I placed the statue on bed of marker cards and geometries so I can also capture the sides of the statue which I also use for aligning the two scans I created (top and bottom). The scan itself was performed with both cross and parallel line mode taking roughly 5min for scanning. No scan spray was used for scanning.

## Post-Processing
When finishing the single scans it already creates a point cloud so I only had to align using automatic feature alignment (after deleting all unnecessary data from around the object). Afterwards I used Quicksurface to align the scan to the coordinate system and reduce the triangle count to a manageable 4M triangles.

Wood Statue of Bird Nest - Einscan Rigil

## Scanning
Scanning was done in sPC connected mode (WiFi, with latest update 120FPS speed) at a moderate high point distance of 0.15mm (can go up/down to 0.05mm but at 0.15mm it already resulted in a 20M triangle file...) until target quality was reached.
I placed the casting on bed of marker cards and geometries so I can also capture the sides of the casting which I also use for aligning the two scans I created (top and bottom). The scan itself was performed with both cross and parallel line mode taking roughly 5min for scanning. No scan spray was used for scanning.

## Post-Processing
When finishing the single scans it already creates a point cloud so I only had to align using automatic feature alignment (after deleting all unnecessary data from around the object). Afterwards I used Quicksurface to align the scan to the coordinate system and reduce the triangle count to a manageable 4M triangles.

Wax Portrait Virgin Mary - Einscan Rigil

This is the R36-Eruptor, which as far as i know, fires 15mm projectiles, which explode on impact. ive nicknamed these rounds "HEFAP" or High Explosive Fragmenting Armor Piercing.

R36-Eruptor Remodel

These are truly some of the best Western campaigns I have ever seen. All of them… I’ve printed them both at 28 mm and 15 mm scale and their flawless.. They are realistic, And have depths and character, lacking the cartoony style of other campaign creators… I highly recommend all five campaigns from this Studio!

3D Print of 15mm Adobe House Work in Progress

6-15mm Free Napoleonic Sentries (Austria, Bavaria, Russia, Württemberg) NAP-25

The Forgemaster's gift to the community. Free. The Forgemaster Dagger is a full-scale 3D printable cosplay prop, support-free, multicolor-ready, with built-in LED channels so it glows from within. This is a free model from our upcoming Kickstarter campaign The Eternal Forge: Fantasy vs Grimdark Collection — launching April 7th. If you like what you see, follow our campaign and don't miss the Early Bird rewards. 👉 https://www.kickstarter.com/projects/meniatures/the-eternal-forge-fantasy-vs-grimdark-collection Printed it and loving it? Show us! Share your make on social media and tag us, every post helps spread the word and brings more people to our Kickstarter campaign. Let's build this community together! 💪 📸 Instagram / TikTok: @MEniatures https://www.instagram.com/me_niatures/  ⚠️ Important: This model is free for personal use only. If you'd like to sell prints, you'll need to grab a commercial license, available through our Kickstarter campaign. 💡 LED Parts List Here are the exact components we used to light up the dagger: LED strip: 3mm COB LED strip with built-in 5V battery pack  Switch: 10x15mm rocker switch (ON/OFF) Both are very affordable and easy to find. We also recommend using transparent filament for the core so the light shines through beautifully!    FEATURES: -Support-free-Multicolor-ready-LED integration-Easy assembly-Blade available in two sizes — full-size for large bed printers and a scaled version for smaller beds-Blade available in two versions — single piece, or split in two parts for easy multicolor printing-Hollow blade interior — ready for LED lighting-Handle available in two versions — solid, or with a pre-cut hole for an on/off switch for the LED lights  

[FREE] Forgemaster Dagger --LED Ready Cosplay Prop | Fantasy vs Grimdark Kickstarter Campaign

Pistola da 10 mm da fallout4/76 pistola modulare da Fallout 4 , fedele al 90%. Per completare l'assemblaggio occerrà una molla da biro per il movimento del grilletto, due perni da 6mmX35mm per bloccare il castello 1,3 e 4 insieme , 4 perni da 3mmX15mm per bloccare il castello 1, 5 e 6 insieme. Facoltativa una vite senza fine da 4 mm  da 10cm per aggiungere un ulteriore supporto ai vari incastri . Assente la texture sul calcio , non sono stato in grado di aggiungerla.

Pistola 10mm -Fallout4

The model includes three options: a classic round base, a custom stool base, and a version without a base for custom placement or kitbashing.Murloc Bob height - 38 mm, Stool base height - 15mm, classic base height - 5.5mm I recommend printing in resin. FDM printing is possible with a 0.2mm nozzle, but you will need to generate your own supports. Both pre-supported (resin) and unsupported STL files are included. This is a fanart model. All rights belong to their respective owners.--------------------------------------------------------------------------------------------------------------------------------------------- If you like this model, feel free to check out my other miniatures in my store. You can use this discount code for 35% off: DHBRUTE35(It works for my entire store, both individual items and bundles)

Murloc Bob – Hearthstone Fan Art Miniature

Bring a touch of charm and functionality to your workspace with this adorable Sleeping Baby Elephant Phone Holder. Designed as both a decorative nursery accessory and a practical gadget, this model features a cute elephant in a resting pose with its trunk elegantly curved upward to securely cradle your smartphone. The sturdy base ensures perfect stability on any desk or nightstand. Optimized for both FDM and Resin 3D printing, the model captures fine details like the matte skin texture and peaceful facial expression. It is a support-free friendly design (depending on orientation) and makes for a perfect gift for animal lovers or a unique addition to a child's room. Recommended Print Settings: - Material: PLA (Matte Grey looks best) or Resin. - Infill: 15-20% for weight and stability. - Layer height: 0.15mm - 0.2mm for crisp details. - Supports: Minimal required under the trunk curve. - Scale: 100% fits most modern smartphones horizontally and vertically.

Sleeping Baby Elephant Phone Holder

Upgrade your workspace with this Mechanical Industrial Gear Cable Organizer. Designed with a rugged, heavy-duty aesthetic, this functional gadget features rotating gears that allow you to wind and manage cables with ease. The integrated sturdy desktop clamp ensures a secure fit on any table edge, keeping your workspace clutter-free and professional. Optimized for both FDM and Resin printing, the model captures intricate metallic textures and mechanical details. For the best results on FDM printers, we recommend a 0.15mm layer height with 20-25% infill for durability. No supports are needed for the main gear teeth, but a brim is suggested for the clamp screw. Whether you are a fan of steampunk aesthetics or industrial design, this slate grey gear winder is the perfect blend of form and function. Ideal for USB cables, charging leads, and headphone wires.

Industrial Gear Cable Winder & Desk Clamp

Elevate your interior decor with this stunning Geometric Spiral Vase. Featuring a sophisticated honeycomb texture and a modern spiral silhouette, this model is specifically engineered for high-quality 3D printing. The design ensures maximum stability with a weighted base and is optimized for support-free printing, making it an ideal project for both beginners and pros. This versatile model is perfect for FDM printers using PLA, PETG, or specialty matte filaments to achieve that elegant emerald look, and it also performs beautifully on large-scale Resin printers. Use it as a standalone art piece or a functional dry flower holder. Print Settings Recommendations: - Layer Height: 0.15mm - 0.25mm - Perimeters: 2-3 for strength - Infill: 10-15% (or use 'Vase Mode' for a decorative version) - Supports: None required - Material: FDM (PLA/PETG) or Resin

Geometric Spiral Honeycomb Vase - No Supports

Chair Y 4DB B2-9D - YM93 /Kb00/Nb00/D15P/H15mM-3D(M26.B11.G24.W03) (Black)

License: CC BY 4.0

This model is an exact digital replica of a real chair manufactured by Metta. All geometric dimensions correspond to the physical sample. The materials are rendered in realistic PBR quality. The model is in its final polished state.

Our website: https://metta-germany.com/en-de/?utm_source=forum_3do&utm_campaign=sketchfab

Create your own chair in our 3D configurator: https://metta-germany.com/en-de/constructor/?utm_source=forum_3do&utm_campaign=sketchfab

Office chair Metta

Tired of messy cables on your desk? This Sleeping Stone Golem Cable Organizer combines fantasy aesthetics with practical desk management. Designed to look like an ancient granite guardian, this heavy-based gadget features rocky arms and natural s specifically modeled to secure your charging wires and USB cables. This 3D model is optimized for both FDM and Resin printing. For the best result, we recommend using matte grey or 'stone' effect PLA to highlight the detailed rocky texture without the need for painting. The wide, stable base ensures it won't tip over, even with multiple heavy braided cables. Print Settings: - Material: PLA (Stone/Granite) or Tough Resin - Layer Height: 0.15mm - 0.2mm - Infill: 20% (Grid or Gyroid for weight) - Supports: Minimal needed (designed with 3D printing in mind) Perfect for gamers, tech enthusiasts, and fans of tabletop aesthetics!

Sleeping Stone Golem Cable Holder & Organizer

For full functionality, we recommend downloading the source format.The Converted version is intended exclusively for browser preview. In the original file, the following are fully preserved:✔ full scene structure✔ unsimplified materials✔ correct PBR texture maps✔ correct object namesIf you are going to integrate the model into a project, choose the original version.Drillpro 115mm Wood Carving Disc Titanium Coated 6 Round Carbide Inserts Angle Grinder Disc Wood Shaping Disc Woodworking Cutting Disc

Wood Carving Disc Titanium Coated

Add a touch of charm and functionality to your workspace with this adorable Sleeping Baby Elephant Phone Holder. Designed with both aesthetics and utility in mind, this 3D model features a cute elephant in a peaceful slumber, with its trunk elegantly curved upward to securely cradle your smartphone in both portrait and landscape modes. The sturdy flat base ensures maximum stability on office desks, bedside tables, or kitchen counters. Optimized for both FDM and Resin 3D printing, this model prints beautifully without complex supports. For a premium look, we recommend a matte slate grey filament or resin to achieve a sophisticated stone-like finish. Print Settings Recommendations: - Layer Height: 0.15mm - 0.2mm for FDM / 0.05mm for Resin. - Infill: 15-20% (Gyroid recommended for weight). - Material: PLA, PETG, or Tough Resin. - Supports: Minimal needed under the trunk. Perfect as a gift for elephant lovers or as a unique desk accessory!

资源库

关于这些资源